Fujitsu SPARC ENTERPRISE M3000 Manuel d'utilisateur Page 169
- Page / 212
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 14 Fan Backplane Replacement 14-5
14.2 Removing the Fan Backplane
1. Remove the signal cable for the operator panel (1 in FIGURE 14-3).
The cable is on the right side of the fan backplane.
2. Remove the signal cable connector for the motherboard unit (2 in
FIGURE 14-3).
The cable connector is on the rear side of the fan backplane.
3. Remove the four screws securing the fan backplane (3 in
FIGURE 14-3).
FIGURE 14-3 Removing the Fan Backplane
4. Remove the fan backplane from the server, and place it on a conductive mat.
A part
A part
1
2
3
3
3
3
- SPARC Enterprise 3
- M3000 Server 3
- Service Manual 3
- Contents 7
- Contents vii 9
- Contents ix 11
- Contents xi 13
- Abbreviations Abbreviations–1 14
- Index Index–1 14
- Glossary 15
- M3000 Server Documentation 17
- Book titles Manual codes 18
- Preface xvii 19
- Text Conventions 20
- Prompt Notations 20
- This Product 21
- Alert messages in the text 22
- Notes on Safety 23
- Ω. The grounding 24
- Preface xxiii 25
- Alert Labels 26
- Product Handling 27
- Limitations and Cautions 28
- Preface xxvii 29
- 1.1 ESD Precautions 31
- 1.2 Server Precautions 33
- Hardware Overview 35
- Server (Front View) 37
- 123456 7 38
- 2.2 Operator Panel 39
- 2.2.1 Operator Panel Overview 40
- Switches (Operator Panel) 41
- Mode Switch Function 42
- LEDs on the Operator Panel 43
- TABLE 3-1 45
- 789101112 48
- 2.5 Labels 51
- Label Locations 52
- Outside: Standards label 52
- Troubleshooting 53
- 3.2 Failure Diagnostic Method 54
- Diagnostic Method Flowchart 55
- Configuration 56
- XSCF> showhardconf 57
- Configurations 58
- # showrev 59
- XSCF> version 59
- 3.4 Error Conditions 60
- Chapter 3 Troubleshooting 3-9 61
- 3.4.2 Monitoring Output 62
- 3.4.3 Messaging Output 62
- XSCF> showstatus 67
- FANBP_B Status:Normal; 67
- XSCF> 67
- 3.5.4.1 fmdump -V Command 68
- 3.5.5 Using the fmadm Command 69
- 3.5.5.2 fmadm repair Command 70
- 3.5.5.3 fmadm config Command 70
- Commands 71
- 3.6.1.1 Options 72
- 3.6.2.1 Options 73
- 3.6.3.1 Options 76
- The prtconf output continued: 77
- 3.6.4.1 Options 78
- 3.6.5 Using the ping Command 79
- 3.6.6 Using the ps Command 80
- 3.6.6.1 Options 81
- 3.6.7.1 Options 82
- FRU Replacement Preparation 83
- 4.2.1 FRU Replacement 84
- 4.2.2 FRU Installation 85
- # cfgadm -a 87
- # cfgadm -c unconfigure Ap_Id 87
- # cfgadm -c configure Ap_Id 88
- TABLE 2-3 and TABLE 2-5 93
- 4.5.1 Powering off the Server 94
- 4.5.3 Powering on the Server 95
- XSCF> poweron -a 96
- Internal Components Access 101
- FIGURE 5-1) 102
- 5.2.1 Removing the Top Cover 103
- 5.2.2 Attaching the Top Cover 104
- 5.3.1 Accessing the Air Duct 105
- 5.3.2 Removing the Air Duct 105
- 5.3.3 Attaching the Air Duct 106
- 5.4.1 Removing the Fan Cover 107
- 5.4.2 Attaching the Fan Cover 108
- Motherboard Unit Replacement 109
- Motherboard Unit Location 111
- 1 Memory (DIMM) 112
- 2 PCIe card 112
- 3 Shutter unit 112
- 12. Remove the shutter unit 114
- Removing the Motherboard Unit 116
- 6.4 Reassembling the Server 117
- 10. Check the hardware 118
- Location number Component 120
- 7.1 Memory Mounting Rules 121
- 2. Mount DIMMs in group B 124
- 7.2 Accessing the DIMMs 125
- 7.3 Removing the DIMMs 126
- 7.4 Installing the DIMMs 127
- 7.5 Reassembling the Server 127
- PCIe Cards 129
- PCIe Slot Locations 130
- 8.1 Accessing a PCIe Card 131
- 8.2 Removing a PCIe Card 132
- 8.3 Mounting a PCIe Card 132
- 8.4 Reassembling the Server 133
- Hard Disk Drive (HDD) 135
- Hard Disk Drive Location 136
- FIGURE 9-2)to 137
- FIGURE 9-2) 137
- Removing a Hard Disk Drive 138
- 9.4 Reassembling the Server 139
- Replacing the Hard Disk Drive 141
- Backplane 141
- FIGURE 10-2) 144
- 10.4 Reassembling the Server 146
- CD-RW/DVD-RW Drive Unit 147
- (DVDU) Replacement 147
- FIGURE 11-2) 149
- FIGURE 11-2), push the CD 150
- 11.4 Reassembling the Server 151
- Power Supply Unit Replacement 153
- 1 Power supply unit (PSU#0) 154
- 2 Power supply unit (PSU#1) 154
- XSCF> replacefru 155
- FIGURE 12-2) 156
- 12.4 Reassembling the Server 157
- Fan Unit Replacement 159
- Fan Unit Locations 160
- 13.1 Accessing a Fan Unit 161
- 13.2 Removing a Fan Unit 161
- Removing a Fan Unit 162
- 13.3 Mounting a Fan Unit 163
- 13.4 Reassembling the Server 163
- Fan Backplane Replacement 165
- Fan Backplane Location 166
- FIGURE 14-2), and incline 167
- FIGURE 14-2) 167
- Removing the Fan Cage 168
- FIGURE 14-3) 169
- 14.4 Reassembling the Server 170
- Operator Panel Replacement 173
- Operator Panel Location 174
- 2. Loosen the one thumbscrew 176
- 15.4 Reassembling the Server 177
- Components List 179
- FRU List 183
- B.2 Motherboard Unit 184
- B.2.1 Memory (DIMM) 185
- B.2.2 PCIe Slot 185
- B.2.3 CPU 186
- B.2.4 XSCF Unit 186
- B.3 Drive 187
- B.4 Power Supply Unit 188
- B.5 Fan Unit 189
- APPENDIX 191
- C.1 Serial Port 192
- C.2 UPC Port 192
- C.3 USB Port 193
- C.4 SAS Port 193
- D-sub 9pin 194
- UPS Controller 195
- D.2 Signal Cable 196
- Appendix D UPS Controller D-3 197
- D.4 Power Supply Conditions 198
- D.5 UPS Cable 199
- D.6 Connections 200
- DC Power Supply Model 201
- E.1 The Server Views 202
- Electrical Specifications 205
- Abbreviations 207
Produits connexes et manuels pour Ordinateurs Fujitsu SPARC ENTERPRISE M3000
(56 pages)
(26 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels