Fujitsu MX130 Manuel d'utilisateur Page 54
- Page / 256
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
54 Upgrade and Maintenance Manual MX130 S2
Basic hardware procedures
4.5 Closing the server
V CAUTION!
● Before attaching the covers, make sure no unnecessary parts or tools
are left inside the server.
● In order to comply with applicable EMC regulations (regulations on
electromagnetic compatibility) and satisfy cooling requirements, the
PRIMERGY MX130 S2 server must not run while the server cover is
removed.
● For further safety information, please refer to chapter "Important
information" on page 31.
4.5.1 Mounting the server cover
Figure 9: Mounting the server cover
Ê Fit the server cover on the chassis.
- PRIMERGY MX130 S2 1
- Certified documentation 2
- Copyright and Trademarks 2
- Before reading this manual 3
- MX130 S2 10
- Contents 14
- Version history 15
- 1.2 Notational conventions 19
- Introduction 20
- 2 Before you start 21
- 2.2 Average task duration 26
- 2.3 Tools you need at hand 27
- D3090 / D3091 28
- Before you start 30
- 3.2 ENERGY STAR 39
- 3.3 CE conformity 42
- 3.5 Environmental protection 44
- Important information 46
- 4 Basic hardware procedures 47
- Basic hardware procedures 51
- Ê Remove the server cover 51
- 4.3 Opening the front cage 52
- Connecting power cord 56
- 6.1 Standard PSU 70
- Power supply 71
- Figure 16: Removing the PSU 72
- 6.1.1.5 Installing the PSU 73
- POWER12V 76
- 7.1 Basic procedure 81
- 7.2 Mounting order 82
- 7.3.1 Required tools 83
- 7.3.2 Preliminary steps 83
- 7.3.4 Concluding steps 87
- 7.4.4 Concluding steps 91
- 7.5.1 Required tools 91
- 7.5.2 Preliminary steps 91
- 7.5.4 Concluding steps 93
- 3.5-inch chassis bay 94
- 7.6.4 Concluding steps 96
- 7.7.1 Required tools 97
- 7.7.2 Preliminary steps 97
- 7.7.4 Concluding steps 100
- 7.8.1 Required tools 100
- 7.8.2 Preliminary steps 100
- V CAUTION! 103
- HDDs and accessible drives 105
- ODD/HDD bracket 106
- 5.25-inch ODD/HDD bracket 107
- 7.10.2 Preliminary steps 107
- 7.10.4 Concluding steps 110
- 7.11.1 Required tools 110
- 7.11.2 Preliminary steps 110
- 7.11.4 Concluding steps 112
- 7.12.1 Required tools 112
- 7.12.2 Preliminary steps 112
- 7.13.1 Required tools 115
- 7.13.2 Preliminary steps 115
- Figure 54: Installing HH ODD 116
- 7.13.4 Concluding steps 117
- 7.14.1 Required tools 118
- 7.14.2 Preliminary steps 118
- Ê Fasten the three screws 122
- 7.15.4 Concluding steps 124
- Ê Remove the three screws 128
- 7.16.4 Concluding steps 129
- 7.17.1 Required tools 130
- 7.17.2 Preliminary steps 130
- 7.17.4 Concluding steps 132
- 7.18.1 Required tools 133
- 7.18.2 Preliminary steps 133
- 7.19.1 Required tools 136
- 7.19.2 Preliminary steps 136
- 7.19.4 Installing the ODD 138
- 7.19.5 Concluding steps 141
- 7.20.1 Required tools 142
- 7.20.2 Preliminary steps 142
- 7.20.4 Concluding steps 144
- 8.1.1 Required tools 146
- 8.1.2 Preliminary steps 146
- System fan 147
- (see circles) 155
- Ê Install the fan cable 156
- 8.1.5 Concluding steps 157
- 9.1 Basic procedure 160
- 9.2 Expansion cards 161
- Expansion cards 162
- 9.2.3 Installing eSATA cable 168
- 9.2.4 Removing eSATA cable 170
- 9.3 Additional tasks 173
- 10.1 Basic procedure 180
- 10.1.2 Operation modes 181
- 10.2.1 Required tools 182
- 10.2.2 Preliminary steps 182
- 10.2.4 Concluding steps 183
- 10.3.4 Concluding steps 185
- Main memory 186
- 11.1 Basic procedure 188
- 11.3.2 Preliminary steps 192
- 11.3.4 Removing the processor 192
- Processors 193
- Ê Latch the socket lever 195
- 11.3.6 Applying thermal paste 196
- 12.1.5 Concluding steps 203
- Figure 127: TPM kit 205
- System board and components 207
- 12.3.2 Preliminary steps 214
- 12.3.5 Concluding steps 221
- 13.1.1 Required tools 224
- 13.1.2 Preliminary steps 224
- Front panel and front USB 226
- 13.1.7 Concluding steps 228
- 13.2.1 Required tools 229
- 13.2.2 Preliminary steps 229
- 13.2.5 Concluding steps 232
- 14.1 Cabling overview 234
- 14.2 Cabling 235
- Configuration with RDX 236
- 14.2.2 Data cabling 237
- Module 2 Channel B 238
- Module 4 Channel B 238
- Module 1 Channel A 238
- Module 3 Channel A 238
- 14.3.1 Required tools 239
- 14.3.2 Preliminary steps 239
- POWER SATA (1) 242
- 14.3.5 Concluding steps 243
- 15 Appendix 245
- 15.1.2 Server rear 246
- 15.1.3 Server interior 247
- 15.2 Configuration tables 248
- Figure 161: Jumper 250
- Appendix 256
Produits connexes et manuels pour Cartes mères de serveurs/postes de travail Fujitsu MX130
(98 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.236 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels