Fujitsu SPARC T5440 Manuel d'utilisateur Page 188
- Page / 212
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
166 SPARC Enterprise T5440 Server Service Manual • June 2011
where x is the CMP/memory module to be enabled.
The following example shows how to enable all the FB-DIMMs on MEM1.
▼ Reset the LDoms Guest Configuration
After reconfiguring the I/O and PCIe fabric, you must recreate your LDoms guest
configurations, as hardware resources that had been previously assigned to your
guests might no longer be available.
1. Power off the system.
2. In the ALOM compatibility shell, type:
3. Power on the system.
4. Recreate your LDoms guests using the remaining hardware resources.
sc> enablecomponent /SYS/MB/MEM1/CMP1/BR0/CH0/D1
sc> enablecomponent /SYS/MB/MEM1/CMP1/BR0/CH0/D2
sc> enablecomponent /SYS/MB/MEM1/CMP1/BR0/CH0/D3
sc> enablecomponent /SYS/MB/MEM1/CMP1/BR0/CH1/D1
sc> enablecomponent /SYS/MB/MEM1/CMP1/BR0/CH1/D2
sc> enablecomponent /SYS/MB/MEM1/CMP1/BR0/CH1/D3
sc> enablecomponent /SYS/MB/MEM1/CMP1/BR1/CH0/D1
sc> enablecomponent /SYS/MB/MEM1/CMP1/BR1/CH0/D2
sc> enablecomponent /SYS/MB/MEM1/CMP1/BR1/CH0/D3
sc> enablecomponent /SYS/MB/MEM1/CMP1/BR1/CH1/D1
sc> enablecomponent /SYS/MB/MEM1/CMP1/BR1/CH1/D2
sc> enablecomponent /SYS/MB/MEM1/CMP1/BR1/CH1/D3
sc> bootmode config="factory-default"
- SPARC Enterprise T5440 Server 1
- Service Manual 1
- Contents 5
- For Safe Operation 13
- Before You Read This Document 13
- Related Documentation 14
- Preface xv 15
- UNIX Commands 16
- Text Conventions 17
- Prompt Notations 17
- Alert Messages in the Text 18
- Notes on Safety 19
- Product Handling 20
- Alert Label 21
- Documentation Feedback 22
- Identifying Server Components 23
- Front Panel Diagram 25
- Front Panel LEDs 27
- Rear Panel Diagram 28
- Rear Panel LEDs 30
- Ethernet Port LEDs 31
- Managing Faults 33
- Server Diagnostics Overview 34
- Diagnostic Flowchart 35
- Diagnostic Flowchart Actions 37
- ILOM Overview 40
- ILOM Fault Management 41
- Oracle VTS Overview 43
- Managing Faults 27 49
- (ILOM show Command) 50
- Controlling How POST Runs 51
- POST Parameters 52
- ▼ Change POST Parameters 53
- ▼ Run POST in Maximum Mode 54
- Managing Faults 33 55
- Detecting Faults 56
- Managing Faults 35 57
- Managing Faults 37 59
- Commands) 61
- ▼ Check the Message Buffer 61
- ▼ View ILOM Event Log 63
- About Oracle VTS Software 64
- Managing Faults 43 65
- Oracle VTS Software Packages 67
- Detecting Faults Using POST 68
- EXAMPLE: PSH Message Output 72
- Managing Faults 51 73
- Clearing Faults 74
- -> show faulty 75
- Disabling Faulty Components 77
- System Recovery 78
- ▼ Disable System Components 79
- ▼ Re-Enable System Components 79
- ILOM-to-ALOM CMT Command 80
- Reference 80
- Managing Faults 59 81
- Managing Faults 61 83
- Safety Information 85
- Safety Symbols 86
- Antistatic Wrist Strap 87
- Antistatic Mat 87
- Required Tools 88
- Remotely 88
- Powering Off the System 89
- Position 91
- 1 Slide Rail Lock 92
- 2 Inner Rail Release Button 92
- ■ Motherboard 93
- ▼ Remove the Top Cover 95
- Servicing Hard Drives 98
- # cfgadm -al 100
- EXAMPLE: Sample Ap_id Output 101
- # cfgadm -c configure c0::sd1 102
- ▼ Remove a Hard Drive 103
- ▼ Install a Hard Drive 104
- Hard Drive Device Identifiers 105
- Servicing Fan Trays 106
- About Fan Trays 107
- Next Steps 108
- ▼ Remove a Fan Tray 109
- ▼ Install a Fan Tray 110
- Fan Tray Device Identifiers 110
- Servicing Power Supplies 111
- About Power Supplies 112
- ▼ Remove a Power Supply 114
- ▼ Install a Power Supply 115
- Power Supply LED 117
- Servicing PCIe Cards 118
- ▼ Install a PCIe Card 119
- ▼ Add a PCIe Card 120
- PCIe Device Identifiers 121
- Related Information 122
- Servicing CMP/Memory Modules 124
- ▼ Remove a CMP/Memory Module 126
- ▼ Install a CMP/Memory Module 127
- ▼ Add a CMP/Memory Module 127
- Servicing FB-DIMMs 130
- ▼ Install FB-DIMMs 131
- ▼ Verify FB-DIMM Replacement 132
- ▼ Add FB-DIMMs 135
- FB-DIMM Configuration 135
- Memory Bank Configurations 136
- FB-DIMM Device Identifiers 138
- Servicing the Front Bezel 141
- ▼ Remove the Front Bezel 142
- ▼ Install the Front Bezel 143
- Servicing the DVD-ROM Drive 144
- ▼ Install the DVD-ROM Drive 145
- Servicing the IDPROM 149
- ▼ Install the IDPROM 150
- Servicing the Battery 151
- ▼ Install the Battery 152
- Servicing the Motherboard 161
- ▼ Install the Motherboard 164
- Servicing the Front I/O Board 172
- ▼ Install the Front I/O Board 173
- ▼ Install the Top Cover 176
- 1 Inner rail release button 178
- 2 Slide rail lock 178
- ▼ Power On the Server 179
- CMP/Memory Module 183
- # cd /mnt 185
- # cp /reconfig.pl 186
- # /mnt/reconfig.pl 186
- ● Do one of the following: 187
- System Bus Topology 189
- Identifying Connector Pinouts 193
- 1 Request to Send 5 Ground 194
- 4 Ground 8 Clear to Send 194
- Serial Port Connector Pinouts 196
- USB Connector Pinouts 197
- Server Components 199
- Customer-Replaceable Units 200
- Field-Replaceable Units 202
- Numerics 205
- Index 185 207
- Index 187 209
- Index 189 211
Produits connexes et manuels pour Serveurs Fujitsu SPARC T5440
Serveurs Fujitsu RX600 Manuel d'utilisateur
(148 pages)
(148 pages)
Serveurs Fujitsu RXI300 Manuel d'utilisateur
(10 pages)
(10 pages)
Serveurs Fujitsu TX300 Manuel d'utilisateur
(122 pages)
(122 pages)
Serveurs Fujitsu D2529 Manuel d'utilisateur
(42 pages)
(42 pages)
Serveurs Fujitsu T5440 Manuel d'utilisateur
(72 pages)
(72 pages)
Serveurs Fujitsu RX600 Manuel d'utilisateur
(134 pages)
(134 pages)
Serveurs Fujitsu BX900 S1 Manuel d'utilisateur
(144 pages)
(144 pages)
Serveurs Fujitsu TX200 S6 Manuel d'utilisateur
(126 pages)
(126 pages)
Serveurs Fujitsu T5220 Manuel d'utilisateur
(112 pages)
(112 pages)
Serveurs Fujitsu T5440 Manuel d'utilisateur
(26 pages)
(26 pages)
Serveurs Fujitsu T850 Manuel d'utilisateur
(18 pages)
(18 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels