Fujitsu SPARC Enterprise Server M3000 Manuel d'utilisateur télécharger pdf (Page 28)

2-8 SPARC Enterprise M3000 Server Service Manual • March 2012

TABLE 2-2 shows the function of the mode switch.

TABLE 2-2 Mode Switch Function

Function Mode Switch

Locked Service

Inhibition of Break Signal Reception Enabled Reception of the

Break signal can be

enabled or disabled for

each domain using

setdomainmode

command.

Disabled

Power On/Off by power button Only Power On is

enabled.

Enabled

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 201 202

SPARC Enterprise M3000 Server 1
Contents 5
Contents vii 7
Contents ix 9
Contents xi 11
Audience 13
Related Documentation 14
Text Conventions 15
Notes on Safety 15
Documentation Feedback 16
1.1 ESD Precautions 17
1.2 Server Precautions 19
Hardware Overview 21
Server (Front View) 23
123456 7 24
2.2 Operator Panel 25
2.2.1 Operator Panel Overview 26
Switches (Operator Panel) 27
Mode Switch Function 28
LEDs on the Operator Panel 29
TABLE 3-1 31
789101112 34
2.5 Labels 37
Label Locations 38
Outside: Standards label 38
Troubleshooting 39
3.2 Failure Diagnostic Method 40
Diagnostic Method Flowchart 41
Configuration 42
XSCF> showhardconf 43
Configurations 44
# showrev 45
XSCF> version 45
3.4 Error Conditions 46
Chapter 3 Troubleshooting 3-9 47
3.4.2 Monitoring Output 48
3.4.3 Messaging Output 48
XSCF> showstatus 53
FANBP_B Status:Normal; 53
XSCF> 53
3.5.4.1 fmdump -V Command 54
3.5.5 Using the fmadm Command 55
3.5.5.2 fmadm repair Command 56
3.5.5.3 fmadm config Command 56
Commands 57
3.6.1.1 Options 58
3.6.2.1 Options 59
3.6.3.1 Options 62
The prtconf output continued: 63
3.6.4.1 Options 64
3.6.5 Using the ping Command 65
3.6.6 Using the ps Command 66
3.6.6.1 Options 67
3.6.7.1 Options 68
FRU Replacement Preparation 69
4.2.1 FRU Replacement 70
■ Hot replacement 71
■ Cold replacement 71
4.2.2 FRU Installation 72
# cfgadm -a 74
# cfgadm -c unconfigure Ap_Id 74
# cfgadm -c configure Ap_Id 75
TABLE 2-3 and TABLE 2-5 79
4.5.1 Powering off the Server 80
4.5.3 Powering on the Server 81
XSCF> poweron -a 82
Internal Components Access 87
FIGURE 5-1) 88
5.2.1 Removing the Top Cover 89
5.2.2 Attaching the Top Cover 90
5.3.1 Removing the Air Duct 90
Removing the Air Duct 91
5.3.2 Attaching the Air Duct 92
5.4.1 Removing the Fan Cover 93
5.4.2 Attaching the Fan Cover 94
Motherboard Unit Replacement 95
Motherboard Unit Location 97
1 Memory (DIMM) 98
2PCIe card 98
3 Shutter unit 98
10. Remove the shutter unit 100
Removing the Motherboard Unit 102
6.4 Reassembling the Server 103
Location Number Component 106
7.1 Memory Mounting Rules 107
Example Mounting DIMM 109
2. Mount DIMMs in group B 110
7.2 Accessing the DIMMs 111
7.3 Removing the DIMMs 112
7.4 Installing the DIMMs 113
7.5 Reassembling the Server 113
PCIe Cards 115
PCIe Slot Locations 116
8.1 Accessing a PCIe Card 117
8.2 Removing a PCIe Card 118
8.3 Mounting a PCIe Card 119
8.4 Reassembling the Server 119
Hard Disk Drive (HDD) 121
Hard Disk Drive Location 122
9.1.1 Active Replacement 123
9.1.2 Hot Replacement 123
9.1.3 Cold Replacement 124
Removing a Hard Disk Drive 125
9.4 Reassembling the Server 126
9.4.2 Hot Replacement 127
9.4.3 Cold Replacement 127
Backplane 129
FIGURE 10-2) 132
10.4 Reassembling the Server 134
CD-RW/DVD-RW Drive Unit 135
(DVDU) Replacement 135
RW Drive Unit 137
FIGURE 11-3) 139
FIGURE 11-3), push the CD 139
11.5 Reassembling the Server 140
Power Supply Unit Replacement 141
1 Power supply unit (PSU#0) 142
2 Power supply unit (PSU#1) 142
XSCF> replacefru 143
FIGURE 12-2) 144
12.4 Reassembling the Server 145
Fan Unit Replacement 147
Fan Unit Locations 148
13.1 Accessing a Fan Unit 149
13.2 Removing a Fan Unit 150
13.3 Mounting a Fan Unit 151
13.4 Reassembling the Server 151
Fan Backplane Replacement 153
Fan Backplane Location 154
FIGURE 14-2), and incline 155
FIGURE 14-2) 155
Removing the Fan Cage 156
FIGURE 14-3) 157
14.4 Reassembling the Server 158
Operator Panel Replacement 161
Operator Panel Location 162
2. Loosen the one thumbscrew 164
15.4 Reassembling the Server 165
Components List 167
FRU List 171
B.2 Motherboard Unit 172
B.2.1 Memory (DIMM) 173
B.2.2 PCIe Slot 173
B.2.3 CPU 174
B.2.4 XSCF Unit 174
B.3 Drive 175
B.4 Power Supply Unit 176
B.5 Fan Unit 177
APPENDIX 179
C.1 Serial Port 180
C.2 UPC Port 180
C.3 USB Port 181
C.4 SAS Port 181
D-sub 9pin 182
UPS Controller 183
D.2 Signal Cable 184
Appendix D UPS Controller D-3 185
D.4 Power Supply Conditions 186
D.5 UPS Cable 187
D.6 Connections 188
DC Power Supply Model 189
E.1 The Server Views 190
E.3 Electrical Specifications 193
Abbreviations 199

Commentaires sur ces manuels

Pas de commentaire

Fujitsu SPARC Enterprise Server M3000 Manuel d'utilisateur Page 28

Commentaires sur ces manuels

Produits connexes et manuels pour Ordinateurs Fujitsu SPARC Enterprise Server M3000