Fujitsu MHZ2250BJ Manuel d'utilisateur Page 175
- Page / 320
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5.3 Host Commands
(24) FLUSH CACHE (X 'E7')
This command is used to write every write cache data stored by the device into the
medium. When the device completes all the data writing, it reports the status to
the host system. The device performs every error recovery so that the data are
read correctly.
• Error reporting conditions
When executing this command, the writing of the data may take several seconds if
much data are to be written.
In case a non-recoverable disk write error has occurred while the data is being
read, the error generation address is put into the shadow block register before
ending the command. This error sector is deleted from the write cache data.
(1) A SATA communication error occurred (ST = 51h, ER = 14h).
At command issuance (Shadow Block Registers setting contents)
CM 1 1 1 1 0 0 1 1
DH x x x x xx
CH
CL
SN
SC
FR
xx
xx
xx
xx
xx
At command completion (Shadow Block Registers contents to be read)
ST Status information
DH x x x x xx
CH
CL
SN
SC
ER
xx
xx
xx
xx
Error information
C141-E280 5-101
- FOR SAFE OPERATION 2
- Revision History 3
- Preface 5
- Operating Environment 6
- Conventions 7
- Attention 7
- Liability Exception 7
- Hot Plug 8
- Important Alert Items 9
- Manual Organization 11
- Contents 13
- Illustrations 19
- CHAPTER 1 Device Overview 23
- 1.1 Features 24
- 1.1.3 Interface 25
- 1.2 Device Specifications 27
- 1.3 Power Requirements 30
- 1.5 Acoustic Noise 34
- 1.6 Shock and Vibration 34
- 1.7 Reliability 35
- (2) Positioning error 36
- 2.1 Device Configuration 42
- 2.2 System Configuration 43
- This page is intentionally 44
- blank 44
- 3.1 Dimensions 46
- 3.2 Mounting 47
- Mounting screw hole 51
- Cable connection 51
- 3.3.1 Device connector 53
- Installation Conditions 54
- 3-10 C141-E280 54
- 4.1 Outline 58
- 4.2 Subassemblies 58
- 4.3 Circuit Configuration 59
- 4.4 Power-on Sequence 62
- Power-on 63
- 4.5 Self-calibration 64
- 4.6 Read/write Circuit 66
- 4.6.3 Read circuit 67
- 4.6.4 Digital PLL circuit 67
- 4.7 Servo Control 68
- Diameter 71
- 4.7.3 Servo frame format 72
- 4.7.5 Spindle motor control 74
- CHAPTER 5 Interface 75
- 5.1 Physical Interface 76
- COMRESET/COMINIT 78
- 106.7 ns 78
- 106.7 ns 106.7 ns 78
- 5.1.4 Connector pinouts 81
- 5.1.5 P11 function 82
- 5.1.6 Hot Plug 84
- 5.2 Logical Interface 85
- 5.2.1 Communication layers 86
- 5.3 Host Commands 101
- Interface 102
- 5-28 C141-E280 102
- 5.3.2 Command descriptions 104
- SN Sector count (15-8) 117
- FR Field = 03 (Mode3) 118
- 5-90 C141-E280 164
- 5.3 Host Commands 165
- Bit 0: Reserved 185
- Setup FIS 185
- → Low Power Idle 197
- → Low Power Idle → Standby 197
- 01h (*1) 198
- • SET MAX ADDRESS 212
- • Description 218
- Sector offset (7-0) 223
- • SCT WRITE DATA (SN = E1h) 237
- Table 5.43 Operation mode 240
- 5.3.3 Error posting 247
- 5.4 Command Protocol 249
- 5.4 Command Protocol 251
- PIO Setup 253
- 5-186 C141-E280 260
- C141-E280 5-187 261
- 5-188 C141-E280 262
- CHAPTER 6 Operations 263
- 6.1 Reset and Diagnosis 264
- earlier than the host) 265
- C141-E280 6-3 265
- 6.1.2 Response to COMRESET 266
- • Security mode state 267
- • SECURITY FREEZE LOCK 267
- • SECURITY UNLOCK 267
- 6.2 Power Save 270
- 6.2.2 Power commands 272
- 6.4 Read-ahead Cache 275
- 6.4.2 Caching operation 276
- 279
- Cache valid data 281
- START LBA 281
- LAST LBA 281
- 6.5 Write Cache 282
- IMPORTANT 283
- 7.1 Maintenance 286
- 7.1.3 Maintenance levels 289
- Disk drive 290
- Firmware 290
- A2 Revision 291
- A3 Revision 291
- 7.1.6 Self-diagnostics 292
- 7.1.7 Test 292
- Figure 7.3 Test flowchart 293
- C141-E280 7-9 293
- 7.2 Operation Confirmation 295
- 7.5 Spare Disk Drive 299
- Glossary 301
- Acronyms and Abbreviations 305
- Comment Form 315
- C141-E280-01EN 317
Produits connexes et manuels pour Matériel Fujitsu MHZ2250BJ
Matériel Fujitsu MHV2120AT Manuel d'utilisateur
(280 pages)
(280 pages)
Matériel Fujitsu MHT2060BH Manuel d'utilisateur
(264 pages)
(264 pages)
Matériel Fujitsu MPD3XXXAT Manuel d'utilisateur
(191 pages)
(191 pages)
Matériel Fujitsu MBA3073NP Manuel d'utilisateur
(138 pages)
(138 pages)
Matériel Fujitsu MAP3735FC Manuel d'utilisateur
(114 pages)
(114 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels