Fujitsu INTEGRATED REMOTE MANAGEMENT CONTROLLER IRMC S2/S3 Manuel d'utilisateur Page 367
- Page / 426
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
iRMC S2/S3 367
Emergency flash
10.4 Emergency flash
If the iRMC S2/S3 firmware can no longer be executed, e.g. because the SDRs
are not compatible with the system, then you can use the emergency mode to
start the firmware running again. In emergency mode, the system automatically
branches to the bootloader and is the ready for the firmware update.
I Emergency mode is indicated by the error LED (global error LED) (rot)
and the identification LED (blue) flashing alternately.
To switch the managed server to emergency mode and then update the
iRMC S2/S3's firmware, proceed as follows:
Ê Disconnect the power supply connector.
Ê Insert the connector in the socket again with the Identify key held down.
The managed server is now in emergency mode.
Ê Boot the server to DOS and use the recovery flash procedure to update the
iRMC S2/S3’s firmware.
I If the firmware is not active then the boot operation may take up to 2
minutes to start. You can ignore the error message “iRMC S2/S3
Controller Error” which the BIOS outputs during this period.
- Remote Management 1
- Certified documentation 2
- Copyright and Trademarks 2
- Contents 3
- iRMC S2/S3 10
- 1 Preface 11
- ● Browser access 13
- ● Security (SSL, SSH) 13
- ● ServerView Integration 13
- ● Power management 13
- ● Local user management 15
- IPMI - technical background 25
- Figure 5: BMC and SOL 28
- ● New iRMC S2 features: 31
- 1.10 Notational conventions 35
- 36 iRMC S2/S3 36
- Notational conventions 36
- 2.1 Requirements 37
- 3 Configuring the iRMC S2/S3 41
- 3.1.1 Prerequisites 42
- Figure 13: Server Mgmt Menu 53
- Figure 17: Server Mgmt menu 60
- 3.4.2 Configuring alerting 64
- 4 User management for the 65
- LDAP login 67
- 4.2 User permissions 68
- 5 Advanced Video Redirection 85
- 5.1 Requirements: 86
- Check the AVR settings 86
- 5.2 Using AVR 88
- 5.2.1 Using a low bandwidth 89
- 5.2.2 Parallel AVR sessions 89
- 5.2.5 Redirecting the mouse 93
- Acceleration=1 99
- Threshold=1 99
- 5.3 Menus of the AVR window 101
- 5.3.1 Extras menu 102
- 5.3.2 Remote Storage menu 105
- 5.3.3 Power Control menu 106
- 5.3.4 Languages menu 107
- 5.3.5 Preferences menu 108
- 6Remote Storage 111
- 6.1.1 Starting Remote Storage 114
- 120 iRMC S2/S3 120
- 122 iRMC S2/S3 122
- 124 iRMC S2/S3 124
- USB 1.1 and USB 2.0 124
- Storage server 127
- 134 iRMC S2/S3 134
- 7 iRMC S2/S3 web interface 135
- 138 iRMC S2/S3 138
- Required user permissions 138
- 140 iRMC S2/S3 140
- 142 iRMC S2/S3 142
- Navigation area 143
- Selected function Title bar 143
- Working area 143
- Interface language selector 143
- Logout button 143
- 7.4 System Information 146
- Information on the server 146
- 7.4.1 System Overview 147
- V CAUTION! 160
- Information on the iRMC S2/S3 165
- 7.7 Power Management 186
- Figure 99: Power On/Off page 187
- 7.7.2 Power Options 191
- I Please note: 194
- ● ASR&R 195
- ● Global Error LED 195
- 7.8 Power Consumption 199
- I Prerequisite: 200
- 206 iRMC S2/S3 206
- Power Consumption 206
- Show server power consumption 207
- 7.9.1 Fans - Check fans 212
- Figure 119: Temperature page 215
- Figure 120: Voltages page 217
- 218 iRMC S2/S3 218
- 7.9.5 Component Status 220
- 7.12 Network Settings 238
- Configure the LAN parameters 238
- 7.13.1 SNMP Trap Alerting 254
- Configure SNMP trap alerting 254
- Configure alerting via modem 255
- 7.14 User Management 263
- Directory 277
- Open LDAP 280
- / Open LDAP / OpenDS 281
- Figure 172: Login page 288
- 7.15.1 BIOS Text Console 292
- 296 iRMC S2/S3 296
- Select IPMI command and 299
- Enter SAC command directly 299
- (No confirmation prompt!) 299
- I Condition: 300
- I Parallel AVR sessions: 307
- 7.16 Remote Storage 312
- (Remote Manager) 315
- 320 iRMC S2/S3 320
- 8 iRMC S2/S3 via Telnet/SSH 321
- 8.2 Operating Remote Manager 323
- 8.3 Overview of menus 324
- ● Service Processor 325
- ● Change password 325
- ● Start a Command Line shell 325
- ● Console Logging 325
- 8.4 Logging in 326
- 8.6 Required user permissions 330
- 8.7 Change the password 332
- 8.8 System Information 332
- 8.9 Power Management 334
- 8.10 Enclosure Information 335
- Start a SMASH CLP shell 340
- 346 iRMC S2/S3 346
- Command Line Protocol (CLP) 346
- I Requirements: 347
- Manager start window 351
- 358 iRMC S2/S3 358
- 10.3 Updating firmware images 360
- Express or ASP 362
- WinFLIRMCS2 /s 4 364
- Figure 221: FlashDisk menu 365
- 10.4 Emergency flash 367
- 10.5 Flash tools 368
- 12 Appendix 385
- 01 16 - Get Power Off Source 389
- 20 05 - Get Firmware Selector 397
- F1 15 - Get CPU Info 401
- 404 iRMC S2/S3 404
- 406 iRMC S2/S3 406
- F5 45 - Get SEL Entry Text 407
- 422 iRMC S2/S3 422
- 426 iRMC S2/S3 426
© 2020, manymanuals.fr. Tous droits réservés | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels